| 70-059TCP/IP 4.0 试题回顾（2） |
|
|
作者：网友 文章来源：不详  |
person one:
Here s what I can remember:
1. Your company has two WINS servers already installed. You need to install a new WINS server to connect to the internet. How will you configure it?
a. Primary WINS
b. Secondary WINS
c. Caching only
d. Forwarder
(I guessed c. But again I guessed , so be sure to check the answer)
2. Which of the following are valid IP addresses, and which are not? (A drag and drop problem, Cute!)
203.122.153.1 (Valid)
127.96.185.20 (Invalid...Starting octet cannot be 127)
150.206.256.3 (Invalid...An octet cannot exceed from the value 255)
175.207.180.6 (Valid)
3. Your company s subnet mask is 255.255.248.0. Your subnet contains a blend of Windows NT and UNIX machines. You have already assigned them IP addresses from 175.60.8.21 to 175.60.8.49. You want all your Windows NT machines to be assigned IP addresses automatically. Create a scope that consumes all the IP addresses in this subnet. (Another drag and drop situation, where you have to drop the IP addresses in the DHCP scope properties screen)
Include range
From 175.60.8.1 ( 10101111.00111100.00001000.00000001 )
To 175.60.15.254 ( 10101111.00111100.00001111.11111110 )
Exclude range
From 175.60.8.21 To 175.60.8.49
(Make good use of the calculator, or your bust)
4. There were two questions from the transcenders, that a computer .
person two:
I used no books recommended by other members. Just the brain dumps to help me focus on what I ought to know.I used general networking with UNIX TCP/IP knowledge with some NT utilities and that was all.In my thoughts I think TCP/IP is TCP/IP no matter waich Operating system.
Here we go
1)A lot of command line utilities: ARP, NETSTAT, NBTSTAT, NSLOOKUP (know these) as well as PERFOMANCE MONITOR and NETWORK MONITOR. In my test mostly I answered NETSTAT when it appeared.
Question I had include:
a)Which utility will you use to display TCP/IP statisticss in your network(netstat)
b)which utility for IP to physical address(arp)
c)To collect statistics for further analysis(perf mon)
d)to capture packets for analysis(network monito)
2) Know about printing stuff like :What are LPQ, LPD and LPR for?
8) I had 8 scenarios.4 of them had the same requirements and optional required results but each one had different solution.The scenarios had something to do with the the fact that You want to introduce NT server in your network and to enable this server to route:
one said just make it able to route
the other one said enable IP forwarding
the other one one said not only Ip forwarding but also install RIP and so on and so forth.
So I answered invariably as
does not meet
meetsonly required results
meets required and one
meets all
For now this is what I can recall
Well here goes my brain dump-----------
1) there was one question where they give you a exhibit and you are to drag and drop the proper subnet mask for the addresses given and they specify the no. of subnets required
2)they give you a exhibit where wkstn1 cannot connect to server1 ,Both in the same subnet ?
------> subnet mask of wkstn1 makes it lie in a different subnet.
------>change the subnet mask of both the server & wkstn so that they lie on the same subnet (you had to choose two)
3) to capture tcp/ip packets
----->snmp must be installed
4)the buffer of perfmon gets fulll in a min . what to do ?
---->set capture filter (not sure )
5)to check the&nbs[1] [2] 下一页
|
| 声明：本站所发表的全部或部分内容仅代表个人观点，与本站无关，谢谢合作！ |
|
上一篇电脑： 70-059TCP/IP 4.0 试题回顾（1）
下一篇电脑： 70-059TCP/IP 4.0 试题回顾（3） |
用户登录 
新用户注册 
